|
- 380,000 lbs/hr 6-stage SS/acid proof steel evaporation system. high level outfit. Evaporation capacity 190 tons H20/hr. Inlet 150-300 tons/hr, avg 260 tons/hr by dry substance 16%. dry substance of concentrated waste liquor after evaporation 54%-64%, avg 60%. Production warm and hot water available. double pumping system. Automatic washing evaporation units. first and second stage provided w/3 separate parallel units. stripping of condensate and collection system of noncondens- able gases easy to add. Tanks for concentrated waste liquor can be used also pressurized up to 4 bar. Stages 1-3 finned tube falling film units. Mfd by Ahlstrom, blt 1987. 4-6 stage tube rising film units, Mfd by Rauma-Repola, blt 1974. Click here to request more information
- 38760-55890 kg/hr water evaporation, 7-effect falling film evaporator, type F-V111-3, feed rate 51000-67500 kg/hr @ 8.6-12% solids, concentrate rate 11610-12240 kg/hr @ 50% solids, concentrate temperature 56-58 deg C, pasteurising temp 85 deg C, boiling temperatures 1st effect 69 deg C, 2nd 67 deg C, 3rd 64 deg C, 4th 60-61 deg C, 5th 56-58 deg C, 6th 50-54 deg C, 7th 44-49 deg C, finisher 56-58 deg C, steam consumption including pre-heating and pasteurisation 3350-4915 kg/hr @ 85 deg C, power installed/consumption 190/140-190/135 kw. Click here to request more information
- 65,500 lbs/hr (1200 sq m) Buckau Wolf SS Sugar Evaporator. 3 bar pressure rating. Tubes are 31/35 mm OD x 4000 mm long. Click here to request more information
- 61,500 lbs/hr Sanitary 5-effect Mariott Walker falling film evap. 3-A approved. Efficiency 8.18 lb water removal/lb steam. Thermal vapor compression. 5 yrs old. 75,000 lbs/hr. Click here to request more information
- 60,000 lb/hr water evap (7,392 sq ft), Swenson 316SS 2-effect long tube vert evaporator system. Feed flow 3,2,1. Steam consumption approx 30,000 lbs/hr @ 225 psig. 3,796 sq per effect of heating surface. Each steam chest contains (290) 2" OD x 25' long 316SS tubes. Estimated feed flow, up to 225 gpm. 2nd effect separator is rubber lined CS. View Photo! - Click here to request more information
- 54233 lbs/hr (24,600 kg/hr) water evaporation, 304 s/steel 5 effect falling film evaporator, consisting of 3-effects, end stage and high concentrator, mfd by Wiegand. Mechanical vapour recovery design, feed rate skimmed milk 30,000 kg/hr @ 9% TS @ 5-10 deg C, Whey milk 31,600 kg/hr 6 % TS @ 5-10 deg C, full milk 28,620 kg/hr @ 12% TS @ 5-10 deg C, feed out (concentrate) skimmed milk 5,400 kg/hr @ 48-50% TS @ 20-60 deg C, Whey milk 7,600 kg/hr @ 25% TS @ 10-15 deg C, full milk 6,870 kg/hr @ 48-50% TS @ 60 deg C, steam consumption 400-500 kg/hr, system also includes separators, tanks, pumps, valves, and all other ancillaries. View Photo! - Click here to request more information
- Egg Yoke Evaporator. Comprises of a quintuple effect APV Falling Film Evaporator System complete w/ plate type heating elements vapor separators, 5 recirculation transfer pumps & motors. 2 condensate pumps & motors. 5 pre-heaters. Vacuum pump & motor. Barometric condenser. Magnetic feed flow meter and steam flow control valve. All of the exposed liquor surfaces will be constructed from titanium materials In addition the system will be suitable to process food grade solutions consistant w/ the FDA requirements. This evap. will be capable of removing 48,500 #/hr of water from a weak feed solution and to concentrate same to a concentration suitable for subsequent dehydration. The steam requirements will be approximately 5# of evaporation/ # of steam at 25 psig pressure. Also, the system can be convertd to a Thermal-Recompression operation for a modest additional investment which would increase the economy from 5 to approx 6.0. Click here to request more information
- 46,702 lbs/hr (5600 gal/hr), Swenson 6-effect 304SS evaporator system. 10,292 sq ft total. Unit is setup as (2) 3-effect systems running parallel. Feed 7000 gal/hr (5% solids), output 1400 gal/hr (30% solids), steam 18,000 lbs/hr. 1st effect (1) 7'6" dia x 8' str side separator; (1) 2120 sq ft heating element, 36" dia, (225) 1 1/2" OD x 24' long 304SS tubes, rated 50 psi @ 288 deg F shell; (1) circulation pump rated 6200 gpm @ 35'TDH, driven by Coppus steam turbine. 2nd effect (1) 7'6" x 8' separator, SN 80772; (1) 1649 sq ft heating element, 30" dia x 26' long, w/(175) 1 1/2" OD x 24' long 304SS tubes; (1) circulation pump 3600 gpm @ 35'TDH, driven by 100 HP, 3/60/230/460 volt, 1775 rpm motor. 3rd effect (1) 7'6" x 8' separator; (1) 1649 sq ft heating element, 30" dia x 26' long, w/(175) 1 1/2" OD x 24' long 304SS tubes; (1) circulation pump 4800 gpm @ 20'TDH, driven by 40 HP, 3/60/230/460 volt, 1775 rpm motor. 4th effect (1) 5' dia x 7'6" separator; (1) 508 sq ft heating element, 18" dia, (54) 1 1/2" OD x 24' long tubes; (1) 791 sq ft surface condenser, 24" dia x 26' long, (84) 1 1/2" OD x 24' long tubes; (1) circulation pump 1500 gpm @ 20'TDH, driven by 15 HP, 3/60/230/460 volt, 1750 rpm motor. 5th effect (1) 8'6" x 8' separator; (1) 1649 sq ft heating element, 30" dia x 26' long, (175) 1 1/2" OD x 24' long 304SS tubes, mfd by Chem Fab, SN 88003, 15 psi @ 100 deg F; (1) surface condenser 42" dia x 22' long; (1) circulation pump 4800 gpm @ 20'TDH, driven by 20 HP, 1760 rpm motor. 6th effect (1) 7'6" dia x 7'6" separator; (1) 2717 sq ft heating element, (346) 1 1/2" OD x 20' long tubes; (1) 439 sq ft surface condenser, (56) 1 1/4" x 24' long tubes; (1) circulation pump 4800 gpm @ 65' TDH, driven by 200 HP, 3/60/460 volt motor. System also includes control panel and interconnecting vapor and circulation piping. View Photo! - Click here to request more information
- 18227-19613 kg/hr water evaporation, 6-effect falling film evaporator, feed rate 22000-23000 kg/hr @ 5-10 deg C and 8.8% solids, concentrate rate 3723-3977 kg/hr @ 45 deg C and 52% solids, steam jet vapour compression across 3-effects, pasteurisation temp 72-135 deg C, condensate discharge at 4th and 6th effect, steam pressure 160 psig, steam consumption for water evaporation and pasteurisation 1740-2118 kg/hr @ 72-135 deg C. Click here to request more information
- 15,000 - 16,000 kg/hr, 304 s/steel 4-effect falling film evaporator, mfd by MKT-tehtaat (Niro), type MKT-PE-4.05-130-F, Technical info for Separated milk, 16,000 kg/hr raw milk intake, 9% total solids (TS), temperature 4 deg C, 13,000 kg/hr evaporative capacity, 3,000 kg/hr concentrate volume @ 40 deg C, 48% TS of concentrate. Technical info for Separated milk - 15,000 kg/hr raw milk intake, 12% total solids (TS), temperature 4 deg C, 11,200 kg/hr evaporative capacity, 3,800 kg/hr concentrate volume @ 40 deg C, 48% TS of concentrate. Technical temperatures - pre-heating 56 to 85 deg C, holding temperature 76-67-56-40 deg C, Energy and media consumption figures, 2860/2580 kg/hr @ 7 bar (aty), 120 m3/hr @ 20 deg C, Pump consumption 41 kww. View Photo! - Click here to request more information
- 35,000 lbs/hr water evaporation (10426 sq ft), SS Mojonnier 4-effect falling film evaporator. Unit has (4) vert steam chests (1) w/(109) 2" x 240" long tubes; (2) w/(306) 2" x 240" long tubes. (2) 8' dia x 18' vapor separators; (4) product pumps; (1) vac pump. This system is multiple effect steam operated system. Low pressure steam is introduced into 1st effect and vapors are condensed in the last effect w/cooling water. Click here to request more information
- 31,680 lbs/hr Water Evaporation Rogers SS Double Effect Evap. Input 40,000 lbs/hr @ 8.75% solids, output 8,320 lbs/hr @42% solids. 1st effect 2,260 sq ft, 2nd effect 1,095 sq ft. W/ CIP system. Click here to request more information
- 27,557 lbs/hr (12,500 kg/hr) water evaporation, 304 s/steel 3 effect falling film evaporator, mfd by MKT-tehtaat (Niro), Ref # PE-T.1p.Tf-130, feed flow rate 11,200-16,000 kg/hr @ 6 deg C (of skimmed milk), 15,000 kg/hr @ 6 deg C ( full milk), solids output 50-48%, concentrate output 2,100-3,000 kg/hr @ 50 deg C (skimmed), 3,750 kg/hr @ 50 deg C (full), steam consumption 270-340 kg/hr (skimmed), 490 kg/hr (full), cooling water 4-6 m3/hr (skimmed), 6 m3/hr (full), electric consumption 140-236 kw (skimmed), 215 kw (full), pump power rating 45 kw (skimmed/full), Mechanical vapour compression design. Click here to request more information
- 11850 kg/Hr ( 26070 Lbs/Hr) water evaporation Wiegand 304 SS 6 effect falling film evaporator. Steam supply at 1400 KG/Hr @ 3.5 bar.Cooling water required @26 degrees C 37 CBM/Hr. View Photo! - Click here to request more information
- 22,700 lbs/hr water evaporation, 4-effect falling film evaporator, manufactured by Stork. Click here to request more information
- 22,630 lbs/hr water evap, (4,526 sq ft) Blaw Knox 304SS 2-effect FC/LTR evaporator. Effect 1 is forced circulation, effect is recirculating long tube vert. 1st effect consists of (1) 7'6" dia x 12'6" str side 304SS vapor separator, weld dish top, 6' cone btm. Rated vac @ 200 deg F. (1) 1,026 sq ft condenser, 304SS tube side, CS shell side. SN 15416. Shell rated 350 deg F, tubes rated 25 psi @ 350 deg F. Openings shell 1-20", 1-4"; heads 2-20". (1) 6800 gpm @ 75'TDH, Goulds centrifugal pump, SN 204B418-405952, Mdl 3138, Size 14x14x20. Packing gland. Driven by 125 HP, 3/60/440 volt, 1200 rpm drip-proof motor. 2nd effect consists of (1) 10' dia x 11'6" str side 304SS vapor separator, weld dish top, 10' cone btm. SN 15418. Rated vac @ 200 deg F. (1) 3,500 sq ft condenser, 304SS tube side, CS shell side. Shell rated vac @ 200 deg F, tubes rated vac @ 200 deg F. 6' dia x 17'6" long. (2) 304SS Moyno pumps, Form VT, Type XOX, 2RM. Driven by 20 HP, US varidrive, 3/60/230/460 volt, output rpm min 90, max 544. (1) barometric condenser, CS. Mfd by Blaw Knox, SN 15420. Rated full vac @ 200d eg F. 5' dia x 14' str side, weld dish top, 3' cone btm. System also includes (1) 636 sq ft 304SS tube, CS shell side heat exchanger. Mfd by Blaw Knox, SN 15419, NB #3184. Shell rated 50 psi/vac @ 800 deg F, tubes rated 50 psi @ 800 deg F. 26" dia x 14'6" long. Openings shell 1-10", 1-2"; head 2-5". 22,630 lbs/hr water evap, (4,526 sq ft) Blaw Knox 304SS 2-effect FC/LTR evaporator. Effect 1 is forced circulation, effect is recirculating long tube vert. 1st effect consists of (1) 7'6" dia x 12'6" str side 304SS vapor separator, weld dish top, 6' cone btm. Rated vac @ 200 deg F. (1) 1,026 sq ft condenser, 304SS tube side, CS shell side. SN 15416. View Photo! - Click here to request more information
- 10,500 kg/hr water evaporation, s/steel 4-effect + finisher, falling film evaporator, mfd by Pasilac:
effect 1 = (210) 35mm diameter x 6m long tubes with 3859 kg/hr evaporation,
effect 2 = (109) 35mm diameter x 6m long tubes with 2000 kg/hr evaporation,
effect 3 = (151) 35mm diameter x 6m long tubes with 1678 kg/hr evaporation,
effect 4 = (169) 35mm diameter x 6m long tubes with 2050 kg/hr evaporation,
system includes 1- open condensor and 2- pasteurizers. Click here to request more information
- Sanitary 22,000 lbs/hr water evap, (10,000 Kg/hr), 304SS 4-effect falling film evaporator system. Mfd by Balcke Duerr (Babcock). Each effect is 1076 sq ft (100 sq meter) heat transfer area. Heat chest has preheater 107 sq ft (10 sq meter). Heating chest 800mm dia x 6400mm long. W/hinged bolted heads. W/(159) 38mm dia x 1.5mm bwg x 5500mm long tubes at 48mm 60 deg pitch position. Openings steam inlet 428mm dia, steam outlet 710mm x 360mm at right angle, product discharge (2) 100mm, sight glass 80mm, product inlet 65mm, condensate inlet and outlet 65mm each, product inlet (2) 50mm. W/preheater consisting of (3) sets of coils, 9.5 circles of 38mm dia x 1.5mm bwd x 32104mm long. Total (75) circles. W/968 sq ft (90 sq meter) condenser w/(215) sq ft (20 sq meter) preheater. Shell 705mm dia x 3481mm long. W/bolted heads. W/(592) 38mm dia x 1.5mm bwg x 3013mm long. W/preheater consisting of (30) circles of coils 51630mm, 58380mm, 65130mm long respectively. Openings steam inlet 500mm, air outlet 65mm, condensate inlet and outlet 100mm each, condensate inlet 55mm, product inlet and outlet 65mm each. (4) separators 1000mm dia x 2000mm str side, weld dish top, bolt hinged btm. Overall hegith 3000mm. Openings product inlet 200mm x 350mm, steam outlet 350mm, product outlet 65mm. Settling tank 1000mm dia x 1100mm str side, dish top, concave btm. Mtd on legs. Openings product inlet 65mm dia, product outlet 50mm dia, condensate inlet 40mm, recycled outlet 40mm. View Photo! - Click here to request more information
- 9,800 kg/hr water evaporation, s/steel falling film evaporator, mfd by Van Der Ploeg, 9 to 35% solids, 14,000 ltr input, 4,200 ltr output, 7,000 ltr/hr of steam. Click here to request more information
- 20,000 lbs/hr (273 sq ft) 3-effect, falling film evaporator. 8.6% solids in. 32-40% skim buttermilk solids out. 25,000 lbs/hr feed. Energy efficient, Thermal recompression. Click here to request more information
- 19000 KG/Hr water evaporation, Wiegand,SS 3 effect falling film evaporator. With mechanical vapor compression. System includes three evaporator bodies, plate heat exchanger, surface condenser, radial compressor, steam compressor, vacuum pumps, feed pumps, controls, control panel. Energy requirements Steam @ 8 bar ,300 KG/ Hr. Cooling water 19000 liter /Hr. Click here to request more information
- 19000 kg/hr water evaporation, 304SS. 6 effect evaporator. MFD by Niro. Click here to request more information
- 17,636 lbs/hr (8,000 kg/hr) water evaporation, 4-effect 304 s/steel falling film evaporator, mfd by MKT-tehtaat (Niro), Thermal vapour recovery design. Click here to request more information
- 7,800 kg/hr water evaporation, s/steel falling film evaporator, mfd by Van Der Ploeg, 9 to 35% solids, 11,000 ltr input, 3,200 ltr output, 5,000 ltr/hr of steam. Click here to request more information
- 16,534 lbs/hr (7,500 kg/hr) water evaporation, 304 s/steel 3-effect falling film evaporator, mfd by MKT-tehtaat (Niro), Mechanical vapour compression design. Click here to request more information
- 16,490 lbs/hr water evap, (3,298 sq ft) Swenson single effect LTV-TVR evaporator. Heating element contains (350) 1 1/2" x 24' long 304SS tubes comprising 3,298 sq ft of surface. Heating element 36" dia x 24', 20% 304SS clad. Vapor body 11'6" dia x 7'1" long SS, 20% 304SS clad. W/flanged top vapor dome 50" dia which has (1) 24" dia and (1) 16" dia vapor outlets. Vapor body has (1) 18" manway and sight glass. Btm liquor box 20% 304SS clad. Auxiliaries (1) thermo compressor; (1) barometric condenser. View Photo! - Click here to request more information
- 13,200 lbs/hr (6,000 kg/hr) Water Evaporation Triple Effect 304 SS Falling Film Evaporator. W/ thermal vapor compression. Built in 1982. Mfg by Chema Bulke Duerr.Click here to request more information
- Sanitary 11,000 lb/hr water evap (5000 Kg/hr) 304SS 3-effect falling film evaporator system. Mfd by Balcke Duerr (Babcock). 1st effect 968 sq ft (90 sq meter), int rated full vac, shell rated 114 psi (7.85 bar). W/double preheater 150 sq ft (14 sq meter). Heating chest has (151) 38mm dia x 1.5mm bwg x 5000mm long tubes on 48mm triangular 60 deg pitch. Body 700mm dia x 5000mm long. Overall height 5926mm. Heads are swing bolted. Top preheater coil has 13.5 circles of 38mm dia pipe x 1.5 bwg x 35057mm long. Lower preheater has (16) circles of 38mm dia x 1.5mm bwg x 41375mm long. 2nd and 3rd effect are 592 sq ft (55 sq meter) each w/double preheaters of 75.3 sq ft (7 sq meter). Int rated full vac, shell rated 114 psi (7.85 bar). Heating chests are 521mm dia x 5000mm long. Overall height 5836mm. W/hinged bolted heads. W/(85) 38mm dia x 1.5mm bwg x 5000mm long tubes on 48mm triangular 60 deg pitch. Top part of the 2nd effect chest preheater has 16.5 circles, 38mm dia x 1.5mm bwg x 29530mm long coil. Lower preheater has 16.5 circles, 38mm dia x 1.5mm bwg x 34300mm long coil. Product inlet 40mm, product outlet 65mm, steam inlet 300mm dia, steam outlet 200mm x 350mm dia @ right angle. (3) separator vessels rated full vac, 990mm dia x 1250mm str side, dish top, hinged bolt btm. Lugs for mounting. Shell 4mm thick, heads 5mm thick. Openings product inlet 200mm x 350mm @ right angle, top head 350mm steam outlet, 50mm product outlet in btm head, 2-50mm sight glasses, (1) settling tank 800mm dia x 1000mm str side. Mtd on legs. (1) 484 sq ft (45 sq meter) condenser, rated 2 bar shell, 3.5 bar on tube side. Shell 530mm/770mm dia x 3403 long. W/(296) 3200mm long tubes on 23mm 60 deg triangular pitch. Shell has coil preheater consisting of (2) sets of 20.5 circles, each 4982mm long. Openings steam inlet 400mm, air discharge 80mm, cooling water outlet 80mm, cooling water inlet 80mm. Condensate inlet 50mm, outlet 65mm. Product inlet and outlet 40mm dia. Circulating pumps are Mdl KAP12, rated 56 gpm (12.7 cbm/hr). Driven by 2.2 KW, 3/50/220/380 volt, 2850 rpm motors. View Photo! - Click here to request more information
- 10,560 lbs/hr (4800 Kg/hr) water evaporation, 304SS 3-effect falling film evaporator. 121.97 sq meter heat transfer area. Mdf by MKT/Niro (Finland). 1st effect 1100mm dia x 4300mm overall length w/top conical head 800mm dia. (196) 42.4mm/37mm dia x 4200mm long tubes. 1st effect preheater 460mm dia x 3220mm long. 2nd effect 630mm/700mm dia x 4300mm long. (14) 33.7mm/27.5mm dia x 3200mm long tubes. 3rd effect 1070mm/1150mm dia x 3200mm long. (19) 204mm/197mm dia x 3200mm long tubes. 1300mm dia separator. System includes Sihi vac pump, driven by 5.5 KW, 3/50/380 volt, 1500 rpm motor. (3) centrifugal pumps, Type FP722/145, driven by 2.2 KW, 3/50/380 volt, 3000 rpm motors. (1) Type MKTEV150 pump driven by 2.2 KW, 3/50/380 volt, 3000 rpm motor. (1) Type PF-24 pump driven by 5.5 KW, 3/50/380 volt, 3000 rpm motor. (1) Type FP742/185 pump driven by 4 KW, 3/50/380 volt, 3000 rpm motor. All interconnecting piping. Gauge panel.. View Photo! - Click here to request more information
- 5,000 kg/hr water evaporation, 304 s/steel 4-effect falling film evaporator, mfd by Wolf. Click here to request more information
- 8,818 lbs/hr (4000 kg/hr) water evaporation, 304 s/steel 3-effect falling film evaporator, mfd by Holvrieka, Thermal vapour recovery design, manual operation. Click here to request more information
- Falling Film Evaporator 8000 kg/hr. Manufacturer Wiegandd. Click here to request more information
- 5500 LBS/Hr water vaporation MONEL 400 falling film evaporator system. Mfg in 1998, started in 1999. Preheater 1 has monel 400 tubes, steel shell. Preheater 2 has Monel 400 tubes, 316SS shell. With 1400 sq. ft Monel 400 tubes 316 SS shell heat exchanger. Steam separator, radial type, Monel 400 with vane type demister. Condenser shell and tube type is 720 sq. ft. all 316SS. Circulation pump rated 1700 GPM @ 45 TDH made of Monel 400, driven by 50 kW motor. Pruduct pump rated 12 GPM @ 200 TDH driven by 4 kW motor.Distillate pump rated 17GPM @ 75TDH, driven by 0.75 kW motor. Condensate pump rated 18 GPM @ 75 TDH, driven by 1.5 kW motor. Liquid ring vacuum pump rated 50 CFM @ 26.5" Hg, driven by 5.5kW motor. Click here to request more information
- 5500 lbs/hr water evaporation, monel 400/316 s/steel falling film evaporator system, designed to evaporate 28% Na2S t0 62% Na2S, feed 4500 kg/hr (28%-30% Na2S) 85 deg C, product 2032 kg/hr (60%-62% Na2S) @ 142 deg C, steam 2993 kg/hr @ 4.5 bar (saturated), cooling water 150 cum/hr @ 35 deg C in and 45 deg C out, power 49.25 Kw, 3/50/380 volt, PLC instrumentation, system consists of (1) 890,000Btu/hr double tube pre-heater, inner tubes monel, outer tubes c/steel, (1) 214,000 Btu/hr double tube pre-heater, inner tubes monel, outer tubes 316 s/steel, (1) 1,400 sq ft HEEX shell and tube, inner tubes monel, outer tubes 316 s/steel, (10 monel 400 steam separator, radial type, Vane type demister, (1) 720 sq ft 316 s/steel condenser, (1) 1,700 gpm @ 45 TDH, monel 400 circulation pump, 50 hp motor, (10 12 gpm @ 75 TDH, monel 400 product pump, 4 kw motor, (1) 20 gpm @ 200 TDH monel 400, feed pump, 7.5 kw motor, (1) 17 gpm @ 75 TDH 316 s/steel distillate pump, 0.75 kw motor, (10 18 gpm @ 75 TDH c/steel condensate pump,1.5 kw motor, (1) 50 scfm @ 26.5 Hg vac, 316 s/steel liquid ring vacuum pump, 5.5 kw motor. View Photo! - Click here to request more information
- 5000 kg/hr 304SS 3 effect water evaporator. MFD by GEA Wiegand. Click here to request more information
- 5000 kg/hr, 304SS water evaporator, 3 effect. MFD by V/D. Click here to request more information
- 3,600 lbs/hr (1.8MM BTU/hr) 316SS single effect evaporator system. Unit requires 10'6" x 10' str side 316SS steam chest. Approx 1800 sq ft, all 316SS vert heat exchanger, shell rated 100 psi @ 400 deg F, tubes not rated. 3" OD tubes. Mfd by Envirotech/Goslin-Birmingham, NB #1635, SN 671742. Approx 24" x 20', 316SS heat exchanger, rated 150 psi @ 450 deg F on both sides. Mfd by Manning and Lewis, NB #5265. 2000 gpm @ 50'TDH 316S centrifugal pump w/40 HP motor. W/thermocompressor. View Photo! - Click here to request more information
- 28837
|
